List of software changes for Kanardia instruments.
Release 3.9.2.
New
- Added support for GD40 carbon-monoxide sensor.
Fixes
- Editing of modern engine bar now requires to enable editing in settings.
- Small bug fixes.
Release 3.9.0.
New
- Added air-brake position indicator in Nesis/Aetos.
- Added support for new GPS module for galileo reception.
- Enabled editing of modern engine bar on Nesis/Aetos.
- Added support for 12 cylinders – EGT/CHT.
Fixes
- Fixed Format option in Nesis/aetos. Now it closes raster files first.
- Fixed a lot of small bugfixes.
Release 3.8.5.
New
Fixes
- Small bugfixes
- Digi: Fixed old Lx cluster display orientation.
- Fixed Nesis/Aetos direction of Joyu wheel on some controls in Nesis/Aetos.
- Fixed software reset of Emsis.
- Fixed DaquInfo requests.
- Fixed Indu watchdog reset if no needles were detected.
- Fixed not shown “Roll Target” option in AP settings.
- Fixed regression in old Mabu units.
- Fixed output handling of Boxi 1.2 units.
Release 3.8.2.
Fixes
- Fixed regresion from 3.8: Autopilot parameters were not saved properly in the servo motors.
Release 3.8.1.
Fixes
- Fixed regresion from 3.8: Boxi PTT and AUX handling for hardware version 1.2 (Old Boxi version).
Release 3.8.0.
New
- Emsis got ULPower status item that can be used as a part of display.
- Engine status for RotaxIs and ULPower in Digi.
- Nesis wind arrow threshold speed can be set.
- Support for two carburetors in Nesis/Aetos.
- When 5 or more bars are shown on parameter, min and max value are shown for vertical bars on modern view.
- Added propeller pitch position function
Fixes
- Default engine parameters in Nesis/Aetos are now loaded based on Daqu engine type.
- Horis: Compensate for current roll in Autopilot desired roll.
- Emsis brightness works now correctly, if some other instrument is changing it.
- A lot of small bug-fixes.
Release 3.7.0.
New
- Redesigned Nesis flight planning.
- Rotor RPM now also supports reductor value.
- Emsis optionaly asks for a start fuel level (software tank only).
- Added colective control min/max function.
- Time zone can be defines also in 15 min increments. This was needed for some Australian zones.
- Added Tmp36 sensor as temperature sensor in Daqu.
- Added Altitude bug.
- Added support for EchoUAT device.
- Add status icon for GDL90 devices.
Fixes
- NMEA out support for 4800 9600 and 19200 bauds was added for IGEP version of Nesis III.
- Range of dynon NTC carburator sensor.
- Allow selection of 8 EGT/CHT channels.
- Better About box. It now also shows detected HW and versions.
- Use vector airspace color settings also for infill.
- Better support for ULPower RS232, fix on simulator, fix on Emsis for ULP.
- Fix Nesis/Aetos shutdown action.
- Increase size of Dialog Title bar.
- Fixed radio frequency tuning direction.
- Make AP chart tuning smaller to prevent delays.
- Change frequency of Digi framebuffer controller.
- Airspace info dialog was not shown in flight correctly.
- Route leg switch message is not shown if direct to point is selected.
- Tail color and painting is improved.
- Logbook flight details extract fix for some cases.
- Show EET times on flight plan panel.
- Horis DI airplane flash fix.
- Emsis dialog channel shows channel name.
- Emsis LongEnter blocked in ChannelEdit and ChannelOffset dialogs.
Release 3.6.2.
New
- Add Nesis/Aetos user button option to resize video on modern panel.
- Time zone can be defines also in 15 min increments. This was needed for some Australian zones.
- Added position sensors for C channels.
- Horis NMEA out for TQ-KTX2.
Fixes
- Aetos configuration entry for selecting video input added.
- Daqu range of dynon NTC carburator sensor.
- Nesis/Aetos – Allow selection of 8 EGT channels.
- Emsis improved About box. It now also shows detected HW and versions.
- Nesis – Use vector airspace color settings also for infill.
- Fixed Daqu RotaxIs switch threshold which was always read as 1400.
Release 3.6.1.
Fixes
- Fix Flarm info dialog, sometimes it was not shown.
- Fix Flarm non-directional targets warning.
- Fix Nesis/Aetos alignment of bars in modern view.
- Fix Aetos modern side view current indication.
Release 3.6.0.
New
- New data recording system for Nesis and Aetos.
- Hide logbook item on slave Aetos/Nesis by default, toggle it with password.
- Fast programing with Kanja also.
- Add support for new Indu airspeed sensor.
- Better Nesis/Aetos Rotax iS error diagnostics support, iS status dialog, lane and status information.
- Horis darker colors for low brightness.
- Horis, chrono page was added
- Horis audio output on new 57mm hardware.
Fixes
- Fix IAS/TAS response on Indu indicators.
- Optimize the FLASH usage in Daqu.
- Increase number of decimals in logger coordinate extract. Smoother KML and CSV paths.
- Improve wind indication display True/North.
- Long-touch on map no longer creates user waypoints.
- Parameter editing system was improved.
- No stall warning on takeoff, if this was a second flight with full stop.
- Added fonts for arabic, armenian and hebrew in Nesis.
- Mini Nesis engine monitor on classic page and on navigation page are now automatic when the XML content is empty.
- Update system checks for minimum hardware version supported.
- Fix logbook flight export.
Release 3.5.4.
Fixes
- Increase absolute range of gearbox pressure.
- Fixed daqu handling of isolated channels.
- Fix Daqu crash after changing configuration.
Release 3.5.3.
New
- IN: Support for new IAS sensors on INDU boards.
Fixes
- Fix TAS calculation on Indu indicators.
- Disable Indu filtering of flight time.
- Fixed PowerFlarm detection and communication with latest flarm firmware 6.81.
- Fixed jump to wrong software fuel level if Daqu was restarted on engine startup.
- Improved AHRS Kalman filter.
- Improve static pressure reading on some Indu altimeters.
- Improve kalman filter on takeoff.
- Fixed track adjustment if using magnetic directions.
- Add daqu config option for external resistor for 4-20mA sensors on pressure functions.
- Color of heading rate indication and NoColor is adjusted to more visible.
- Fix heading indication in horis with compass.
- Increase absolute range of gearbox pressure function.
Release 3.5.2.
Fixes
- Fixed problem with integer low pass filter on airspeed sensors.
- Update Avio database for AIRAC 1909.
Release 3.5.1.
Fixes
- Autopilot disable on Joyu is working now. Only working with Nesis&Aetos.
- Add more external serial units for connecting to RS232 port on Nesis III-igep.
- Show traffic on classic screen.
- Leg change deletes direct to waypoint bug fix.
- Export complete logger now exports all data in the logbook. Rollover was tested.
- Fix for odd GPS date – second rollover problem.
Release 3.5.0.
New
- Added autopilot roll and pitch angle target on AHRS display.
- Ability to select second static pressure sensor on newer Airu units.
- Engine logbook dialog added to Service icons.
- Dialog for Airu vibrations FFT added.
- Added new CO level sensor.
- Option for deleting all unnamed user waypoints.
- Info dialog got counters for engine, flight and power-on total time.
- New Traffic message configuration added to tune the text and voice appearance.
- Added option to select different strategy for autopilot roll control.
- Cell voltage of the lithium batteries can be measured.
- Hide logbook item on slave instruments by default, toggle it with password.
Fixes
- RPM Engine and Rotor units can be selected for scale and for text independently.
- Improved autopilot behavior, especially turning on.
- Regression. Selecting AP track with long press on compass rose.
- Improved dialog design, when multiple dialogs are shown the border is seen.
- Resolved bug when focus was lost during first show of virtual keyboard.
- Software fuel level on iS engines was not working.
- Status bar heading bug.
- Red crosses on status bar for most parameters.
- Constellation dialog was can be closed with BACK button.
- Added special KTX2 NMEA GPS output – only RMC sentence.
- Fixed error for software based fuel level. Was merged into 3.4.1.
- GPS date rollover problem for some GPS modules. Merged in 3.4.3
- SSL download enabled.
- Nesis crashed because weather data was not available.
- Fixed fuel level handling for old units.
- Fix reboot problem after route activation.
- AD-AHRS kalman filter optimization.
- Fix logger data angular rate writting. For speeds betwen -10 and 0 deg/s it was zero because of invalid cast.
- Decrease maximum current for smaller servo due to overheating.
- Fix rounding in logger for software tank. No more lost fuel after reboot.
Release 3.4
New
- Initial brightness option was added to Horis.
- Brightness table for Horis 80 was also changed a bit.
- Sunset time. Press on status time shows sunset time for 10s.
- GNSS Constellation added into Options->Info dialog.
- Magu heading reports can be disabled and this is stored in flash.
- Indu option for external knob encoder.
- Support for ULPower CAN protocol.
- Protocol for MW Fly engines added.
- Alarm function on miniDaqu and Emsis.
- New layout system for Nesis and Aetos.
- Engine power can be displayed.
- Cell voltage of the lithium batteries can be measured.
- Added option to select different strategy for autopilot roll control.
- Joyu now works with Horis.
- Minor, mini Daqu 2.9 fix – switch is enabled.
- Added support for Joyu. Nesis was also set, but not Kanja.
- Option for deleting all unnamed user waypoints.
- Info dialog got counters for engine, flight and power-on total time.
- Added new CO level sensor.
Fixes
- CTR and prohibited areas are now filled.
- Engine shutoff bug fixed.
- Daqu offset and channel configuration.
- Automatic scale generation.
- Offset for Daqu sensors moved to proper place.
- Added possibility to disable Magu heading.
- Joyu support in Emsis — for a new Joyu model.
- CO level offset on A20.
- Band editing – limit to previous and next items.
- Daqu Channel configuration fixes. Wrap difference unit test.
- Fix saving fuel parameters.
- Fix port configuration for I2c2.
- Alarm is only active if age is small enough.
- If direction source is changed, burn this into MAGU.
- Corrected WMM2015v2 model.
- Fuel level handling for old units.
- Module configuration service for QNH is brodcasted now.
- Nesis crashed because weather data was not available.
- SSL download handling in Nesis.
- GPS date rollover problem for some GPS modules.
- Stop transmiting internal accelerometer data.
- Added special KTX2 nmea GPS output – only RMC sentence.
- Fixed error for software based fuel level.
- Red crosses on status bar for most parameters.
- Constellation dialog can be closed with BACK button.
- Bias limited.
- Status bar heading bug.
- Software fuel level on iS engines was not working.