List of software changes for Kanardia instruments.

Release 3.9.2.

New

Added support for GD40 carbon-monoxide sensor.

Fixes

Editing of modern engine bar now requires to enable editing in settings.
Small bug fixes.

Release 3.9.0.

New

Added air-brake position indicator in Nesis/Aetos.
Added support for new GPS module for galileo reception.
Enabled editing of modern engine bar on Nesis/Aetos.
Added support for 12 cylinders – EGT/CHT.

Fixes

Fixed Format option in Nesis/aetos. Now it closes raster files first.
Fixed a lot of small bugfixes.

Release 3.8.5.

New

Fixes

Small bugfixes
Digi: Fixed old Lx cluster display orientation.
Fixed Nesis/Aetos direction of Joyu wheel on some controls in Nesis/Aetos.
Fixed software reset of Emsis.
Fixed DaquInfo requests.
Fixed Indu watchdog reset if no needles were detected.
Fixed not shown “Roll Target” option in AP settings.
Fixed regression in old Mabu units.
Fixed output handling of Boxi 1.2 units.

Release 3.8.2.

Fixes

Fixed regresion from 3.8: Autopilot parameters were not saved properly in the servo motors.

Release 3.8.1.

Fixes

Fixed regresion from 3.8: Boxi PTT and AUX handling for hardware version 1.2 (Old Boxi version).

Release 3.8.0.

New

Emsis got ULPower status item that can be used as a part of display.
Engine status for RotaxIs and ULPower in Digi.
Nesis wind arrow threshold speed can be set.
Support for two carburetors in Nesis/Aetos.
When 5 or more bars are shown on parameter, min and max value are shown for vertical bars on modern view.
Added propeller pitch position function

Fixes

Default engine parameters in Nesis/Aetos are now loaded based on Daqu engine type.
Horis: Compensate for current roll in Autopilot desired roll.
Emsis brightness works now correctly, if some other instrument is changing it.
A lot of small bug-fixes.

Release 3.7.0.

New

Redesigned Nesis flight planning.
Rotor RPM now also supports reductor value.
Emsis optionaly asks for a start fuel level (software tank only).
Added colective control min/max function.
Time zone can be defines also in 15 min increments. This was needed for some Australian zones.
Added Tmp36 sensor as temperature sensor in Daqu.
Added Altitude bug.
Added support for EchoUAT device.
Add status icon for GDL90 devices.

Fixes

NMEA out support for 4800 9600 and 19200 bauds was added for IGEP version of Nesis III.
Range of dynon NTC carburator sensor.
Allow selection of 8 EGT/CHT channels.
Better About box. It now also shows detected HW and versions.
Use vector airspace color settings also for infill.
Better support for ULPower RS232, fix on simulator, fix on Emsis for ULP.
Fix Nesis/Aetos shutdown action.
Increase size of Dialog Title bar.
Fixed radio frequency tuning direction.
Make AP chart tuning smaller to prevent delays.
Change frequency of Digi framebuffer controller.
Airspace info dialog was not shown in flight correctly.
Route leg switch message is not shown if direct to point is selected.
Tail color and painting is improved.
Logbook flight details extract fix for some cases.
Show EET times on flight plan panel.
Horis DI airplane flash fix.
Emsis dialog channel shows channel name.
Emsis LongEnter blocked in ChannelEdit and ChannelOffset dialogs.

Release 3.6.2.

New

Add Nesis/Aetos user button option to resize video on modern panel.
Time zone can be defines also in 15 min increments. This was needed for some Australian zones.
Added position sensors for C channels.
Horis NMEA out for TQ-KTX2.

Fixes

Aetos configuration entry for selecting video input added.
Daqu range of dynon NTC carburator sensor.
Nesis/Aetos – Allow selection of 8 EGT channels.
Emsis improved About box. It now also shows detected HW and versions.
Nesis – Use vector airspace color settings also for infill.
Fixed Daqu RotaxIs switch threshold which was always read as 1400.

Release 3.6.1.

Fixes

Fix Flarm info dialog, sometimes it was not shown.
Fix Flarm non-directional targets warning.
Fix Nesis/Aetos alignment of bars in modern view.
Fix Aetos modern side view current indication.

Release 3.6.0.

New

New data recording system for Nesis and Aetos.
Hide logbook item on slave Aetos/Nesis by default, toggle it with password.
Fast programing with Kanja also.
Add support for new Indu airspeed sensor.
Better Nesis/Aetos Rotax iS error diagnostics support, iS status dialog, lane and status information.
Horis darker colors for low brightness.
Horis, chrono page was added
Horis audio output on new 57mm hardware.

Fixes

Fix IAS/TAS response on Indu indicators.
Optimize the FLASH usage in Daqu.
Increase number of decimals in logger coordinate extract. Smoother KML and CSV paths.
Improve wind indication display True/North.
Long-touch on map no longer creates user waypoints.
Parameter editing system was improved.
No stall warning on takeoff, if this was a second flight with full stop.
Added fonts for arabic, armenian and hebrew in Nesis.
Mini Nesis engine monitor on classic page and on navigation page are now automatic when the XML content is empty.
Update system checks for minimum hardware version supported.
Fix logbook flight export.

Release 3.5.4.

Fixes

Increase absolute range of gearbox pressure.
Fixed daqu handling of isolated channels.
Fix Daqu crash after changing configuration.

Release 3.5.3.

New

IN: Support for new IAS sensors on INDU boards.

Fixes

Fix TAS calculation on Indu indicators.
Disable Indu filtering of flight time.
Fixed PowerFlarm detection and communication with latest flarm firmware 6.81.
Fixed jump to wrong software fuel level if Daqu was restarted on engine startup.
Improved AHRS Kalman filter.
Improve static pressure reading on some Indu altimeters.
Improve kalman filter on takeoff.
Fixed track adjustment if using magnetic directions.
Add daqu config option for external resistor for 4-20mA sensors on pressure functions.
Color of heading rate indication and NoColor is adjusted to more visible.
Fix heading indication in horis with compass.
Increase absolute range of gearbox pressure function.

Release 3.5.2.

Fixes

Fixed problem with integer low pass filter on airspeed sensors.
Update Avio database for AIRAC 1909.

Release 3.5.1.

Fixes

Autopilot disable on Joyu is working now. Only working with Nesis&Aetos.
Add more external serial units for connecting to RS232 port on Nesis III-igep.
Show traffic on classic screen.
Leg change deletes direct to waypoint bug fix.
Export complete logger now exports all data in the logbook. Rollover was tested.
Fix for odd GPS date – second rollover problem.

Release 3.5.0.

New

Added autopilot roll and pitch angle target on AHRS display.
Ability to select second static pressure sensor on newer Airu units.
Engine logbook dialog added to Service icons.
Dialog for Airu vibrations FFT added.
Added new CO level sensor.
Option for deleting all unnamed user waypoints.
Info dialog got counters for engine, flight and power-on total time.
New Traffic message configuration added to tune the text and voice appearance.
Added option to select different strategy for autopilot roll control.
Cell voltage of the lithium batteries can be measured.
Hide logbook item on slave instruments by default, toggle it with password.

Fixes

RPM Engine and Rotor units can be selected for scale and for text independently.
Improved autopilot behavior, especially turning on.
Regression. Selecting AP track with long press on compass rose.
Improved dialog design, when multiple dialogs are shown the border is seen.
Resolved bug when focus was lost during first show of virtual keyboard.
Software fuel level on iS engines was not working.
Status bar heading bug.
Red crosses on status bar for most parameters.
Constellation dialog was can be closed with BACK button.
Added special KTX2 NMEA GPS output – only RMC sentence.
Fixed error for software based fuel level. Was merged into 3.4.1.
GPS date rollover problem for some GPS modules. Merged in 3.4.3
SSL download enabled.
Nesis crashed because weather data was not available.
Fixed fuel level handling for old units.
Fix reboot problem after route activation.
AD-AHRS kalman filter optimization.
Fix logger data angular rate writting. For speeds betwen -10 and 0 deg/s it was zero because of invalid cast.
Decrease maximum current for smaller servo due to overheating.
Fix rounding in logger for software tank. No more lost fuel after reboot.

Release 3.4

New

Initial brightness option was added to Horis.
Brightness table for Horis 80 was also changed a bit.
Sunset time. Press on status time shows sunset time for 10s.
GNSS Constellation added into Options->Info dialog.
Magu heading reports can be disabled and this is stored in flash.
Indu option for external knob encoder.
Support for ULPower CAN protocol.
Protocol for MW Fly engines added.
Alarm function on miniDaqu and Emsis.
New layout system for Nesis and Aetos.
Engine power can be displayed.
Cell voltage of the lithium batteries can be measured.
Added option to select different strategy for autopilot roll control.
Joyu now works with Horis.
Minor, mini Daqu 2.9 fix – switch is enabled.
Added support for Joyu. Nesis was also set, but not Kanja.
Option for deleting all unnamed user waypoints.
Info dialog got counters for engine, flight and power-on total time.
Added new CO level sensor.

Fixes

CTR and prohibited areas are now filled.
Engine shutoff bug fixed.
Daqu offset and channel configuration.
Automatic scale generation.
Offset for Daqu sensors moved to proper place.
Added possibility to disable Magu heading.
Joyu support in Emsis — for a new Joyu model.
CO level offset on A20.
Band editing – limit to previous and next items.
Daqu Channel configuration fixes. Wrap difference unit test.
Fix saving fuel parameters.
Fix port configuration for I2c2.
Alarm is only active if age is small enough.
If direction source is changed, burn this into MAGU.
Corrected WMM2015v2 model.
Fuel level handling for old units.
Module configuration service for QNH is brodcasted now.
Nesis crashed because weather data was not available.
SSL download handling in Nesis.
GPS date rollover problem for some GPS modules.
Stop transmiting internal accelerometer data.
Added special KTX2 nmea GPS output – only RMC sentence.
Fixed error for software based fuel level.
Red crosses on status bar for most parameters.
Constellation dialog can be closed with BACK button.
Bias limited.
Status bar heading bug.
Software fuel level on iS engines was not working.