Sensors & Accessories

Rotax kit

Rotax 912/914 sensor kit

  • 4x EGT (K-type thermocouple, screw type M8 x 1)
  • Active fuel pressure sensor and fittings for 1/4” fuel line
  • Current transducer 30 A

Sensors

Cylinder head temperature sensors

CHT probe for Rotax

  • Temperature probe, VDO (0 to 150 °C / 0 to 300 °F)
  • 1/8 – 27 NPT thread
  • For Rotax engines

CHT probe for Jabiru

  • Thermocouple (type J)
  • 12 mm ring terminal
  • For Jabiru engines

CHT probe for Lycoming

  • Thermocouple adjustable bayonet (type J)
  • bushing 3/8”-24, tip 2 1/2” x 3/16”
  • For Lycoming engines

Exhaust gas temperature sensors

EGT probe for Rotax

  • Thermocouple (type K)
  • M8x1 screw type
  • For Rotax engines

EGT probe for Jabiru

  • Thermocouple (type K)
  • Hose clamp 3/4 – 1 3/4”
  • For Jabiru engines

EGT probe for Lycoming

  • Thermocouple (type K)
  • Hose clamp 1/2 – 2”
  • For Lycoming engines

Pressure sensors

Fuel pressure sensor

  • Active fuel pressure sensor (0 to 1 bar / 0 to 15 psi)
  • 1/8 – 27 NPT thread
  • For all engines

Oil/Fuel pressure sensor

  • Active oil or fuel pressure sensor (0 to 10 bar / 0 to 145 psi)
  • 1/8 – 27 NPT thread
  • For all engines

Temperature sensors

Oil/Water temperature sensor

  • Oil or water temperature probe, VDO (0 to 150 °C / 0 to 300 °F)
  • 1/8 – 27 NPT thread
  • For Rotax and Jabiru engines

Oil temperature sensor

  • Oil temperature (100 to 150 °C)
  • 5/8 – 18 UNF thread
  • For Lycoming engines

OAT digital sensor

  • Outside air temperature (OAT) digital sensor.

Other

Rotor RPM sensor

  • Proximity sensor
  • 12  to 24 V  DC

Flow Transducer (Red Cube)

  • Fuel flow sensor FT-60
  • Flow rate: 0.6 to 70+ US GPH
  • For all engines up to 350hp

Current transducer 30 A

  • For currents up to -/+30 A

Fuel pressure sensor fitting 8 mm

  • Fuel pressure sensor fitting – 8 mm hose
  • For Rotax 914 engine

Fuel pressure sensor fitting 6 mm

  • Fuel pressure sensor fitting – 6 mm hose
  • For Rotax 912 engine

Accessories

BLU & Kanja

  • CAN to Bluetooth interface
  • Enables you to configure and upgrade any CAN based Kanardia device

Dimu - Dimmer Control

  • An accessory that allows you to
    adjust brightness
  • Weight: 35 g
  • Size: 20 x 50 x 27 mm
  • Power: 10 mA

Leivin Booster

  • DC-DC Adjustable Step-up Power Converter Module
  • Input voltage: 3 – 34 V
  • Output voltage: 4 – 35 V
  • Output Current: 2.5 A (max)

Power cable

  • Power supply cable for Kanardia products
  • Standard length 1.0 m

Can cable RJ45 - RJ45

  • CAN cable with RJ45 connector on both sides

CAN cable RJ45 - Binder

  • CAN cable with RJ45 connector on one side, Binder (round 5 pole) on the other

Multiple T CAN cable

  • Double, triple and multiple T CAN cable – custom length
  • Provides two or more connections for CAN units

T can junction

  • T junction – three RJ45 connectors
  • Provides one additional connection for new CAN unit

GPS antenna

  • GPS antenna + standard length cable
  • 0.6 m, 0.8 m, 1.2 m

Terminator

  • Plain RJ45 plug with 120 Ω resistor
  • Needed to start and terminate the CAN network